Ø   Full-Travel Alphanumeric Keyboard

Ø   LCD-Defined Soft Keys

Ø   12 Inch High Resolution (800 x 600) Color LCD for Information Display

Ø   Position Display

Ø   Distance To Go Display

Ø   Actual Feedrate Display

Ø   Active Event and Subsequent Events Display

Ø   Part Program Storage and Display, 448,000 Characters

Ø   Buffered Input Allows Part Programs of Unlimited Length to be Executed from Floppy Disk or from an External Source

Ø   Concurrent Operation Allows Part Programs to be Entered or Edited While Cutting a Part

Ø   Fault Messages and Program Text Messages

Ø   Program Zero

Ø   Axis Home

Ø   Clamp Scan

Ø   Axis Jog

Ø   Test Modes and Program Inhibit

Ø   Optional Stop (M01) and Slash Code Block Delete

Ø   On-Line Diagnostics

Ø   Simultaneous Two (X and Y) Axes of Control

Ø   Departures to ± 9999.999 Inches, or ± 99999.99 mm

Ø   Maximum Rapid Rates up to 3,200 1PM or 80 MPM

Ø   Electric Servo Drive Outputs ± 1OV Max

Ø   Interface for Digital Feedback Encoders

Ø   Servo Update Time 2 ms

Ø   Fixed Software Travel Limits

Ø   Part Programmable Software Travel limits

Ø   Customer Initialized Machine Control Parameters

Ø   Auxiliary Functions: M and T Codes

Ø   32 x 32 DC Inputs and Outputs (Bank Selectable for 24VDC or Ground Switching) plus 32 Row/Column Inputs for Operator’s Panel Switches

Ø   PLC Programmable Logic Control with Flash Memory and Message Capability

Ø   Automatic Clamp Scan Cycle via Manual Mode

Ø   Sheet Repositioning Cycle

Ø   Muting Zones to assure that Workpiece Clamps cannot be punched

Ø   Electronic Handwheel(s))

Ø   Part Program Storage Expansion to 896,000 Characters

Ø   RS-422 Serial Port in Place of RS-232 Port

Ø   ONC Terminal Mode

Ø   Customer Prepared Cycles (User Macros) for Custom Culling and Probing Cycles and for Special OEM-Designed Machine Functions

Ø   High-Speed Touch Trigger Probe Interface

Ø   Additional DC Inputs and Outputs

Ø   Programming Format Switchable Between DynaPath® Menu-Driven Conversational and Conventional EIA/ISO  G-Codes

Ø   Parameter Initialized G-Codes for Part Programming Compatibility between different Machines

Ø   Decimal Point Programming

Ø   Inch/Metric input

Ø   Absolute/Incremental Programming

Ø   Radius and Diameter Programming

Ø   Cartesian/Polar Coordinate Programming

Ø   End Point Programming

Ø   Angle-Length Programming

Ø   Angle-Diameter Programming

Ø   Angle-Radius Programming

Ø   Automatic Fillet Generation

Ø   Automatic Chamfer Generation

Ø   Special Events

ü      Three Types of Taper Programming

ü      Seven Types of Thread Programming

ü      Three Types of Groove Programming

ü      Peck Drill Cycle

ü      Tapping Cycle

Ø   Roughing and Finishing Cycles (Two Types to Accommodate both Bar Stock and Castings) to Automatically Cut a Contour Defined by Turn, Face Taper and Arc Events. Inside, Outside or Face Cycles can be Programmed.

Ø   Entry of Speeds and Feeds in Roughing and Finishing Cycles

Ø   Material Data Table for Standard and Special Materials Selected by Operator for Automatic

Ø   Macro Programming Mode, 4 Levels

Ø   High-Resolution Interpolated Graphics Display to Verify Part Profile and Analyze Cutting Time Before Turning the Part

Ø   Conversational Graphics™ for Interactive Graphical Programming Help (The Hard Disk Drive Optional Feature is a Prerequisite for Use of this Feature)

Ø   Modular Configuration:

ü      System Module

ü      CNC Operator’s Panel

ü      Auxiliary Operator’s Panel (Optional)

Ø   System Module Enclosure Hardened for Noise and Vibration Immunity

Ø   CNC Operator’s Panel with Full-Travel Keyboard, Soft Keys and Industrial LCD - Oil and Coolant Tight

Ø   Industrial 586 Passive CPU Board for High Reliability

Ø   Processor Upgradeable to Stay Current with Technology

Ø   High Speed, Serial CANbus Interface for Error Detecting/Correcting Packet Communication with CNC Operator’s Panel and DC/IO

Ø   Machine Interface via Optically Isolated DC Inputs and Short Circuit Protected DC Outputs

Ø   Custom Heavy Duty Switching Power Supply

Ø   Input Voltage: 115/230 VAC± 10% Single Phase, 47-63 HZ. 425 VA

Ø   Ambient Temperature 40°to 120° (4° to 49°C)

Ø   Humidity: 5-95%

Ø   Mating Half of Interlace Connectors and Front Panel Cables

Ø   Bi-directional Lead Screw Error Compensation

Ø   Reversal Error Compensation

Ø   (48) Pairs of Tool Offsets (X, Z) Entered as Radius or Diameter and Absolute or Incremental

Ø   (16) Sets of Tool Geometry Compensation (Tool Size and Tool Nose Radius) with Look Ahead Capability for Work Surface Programming

Ø   (48) Stored Feedrate Override Values which can be Incremented and Decremented in 5% Steps during Cutting

Ø   Calibration Feature for Automatically Storing Tool Compensations

Ø   Load and Store of all Tool Table Data via Interface Ports and Optional Floppy Disk

Ø      Hard Disk Drive for Operating System Storage

Ø      Hard Disk Drive for Machine Control Parameters

Ø      Hard Disk Drive for Large Capacity Local Storage of Part Programs and Tool Tables and for Buffered Input Operations

Ø      3.5 Inch IBM® AT Compatible Floppy Disk Drive with Cover and Cable for Load/Store of Part Programs, Tool Tables, Machine Parameters, PLC Program and System Upgrades and for Buffered Input Operations

Ø      Dual RS-232 Serial Ports (300 to 38,400 Baud) for Load/Store of Part Programs. Tool Tables, Machine Parameters, PLC Program and for Buffered Input Operations

Ø   Jog Mode: 

Continuous Jog,

4 Selectable Rates Incremental Jog,

5 Selectable lncrements

Ø   Reference Zero

Ø   Auto Mode

Ø   Single Event Mode

Ø   Program Mode:

Position    

 Subroutine

Linear Nibble

Dwell

    Arc Nibble

M Function

Rotate

 Frame

      Circle

Grid

Bolt Circle

Pitch

     Repeat

Set-Up

     Clamp Relocate

Text

Macro

Ø   Set Up Mode:

Part Offset

In/MM Selection

Reversal Comp.

Travel Limits

Program Allow/ Inhibit

Test Modes

Home Position Entry

 Scale Factor

 Mirror image

Clamp Positions

Ø   Tool Tables:

Compensations for Rectangular (X,Y) and Circular (D) Tools

Ø   Transmit/Receive Mode

Ø   Learn Mode

Ø   Edit Mode

Ø   Catalog Mode with Capability to Store, Copy and Rename up to 250 Part Programs